-
When to use this checklist
-
Step 1: Pin down the chemistry before you touch anything
-
Step 2: Read the thermal signals
-
Step 3: Verify the charge/discharge pair
-
Step 4: Isolate before you diagnose
-
Step 5: Decide—repair, quarantine, or retire
-
Step 6: Match the disposal path to the device
-
Step 7: Document the disposition
-
Step 8: Close the loop with a visual check
-
What I got wrong
-
The one non-step
When to use this checklist
Last March—the 14th, to be exact—a client called at 6:40 pm. They had a pallet of portable power stations in the 500 Wh range sitting in a warehouse that had lost HVAC for two days. Shipping window was 36 hours. Fourteen thousand dollars of order value on the line. The question was either "can we ship?" or "do we quarantine?"
That call is why this checklist lives on my phone. I'm an operations lead at a battery recovery and safety firm. I've handled 400+ battery incidents in six years, including same-day triage for municipal fire departments and industrial clients with stalled shipments. Most of those incidents were not dramatic. They were the "I should have checked before I plugged that in" kind—five minutes to prevent, five days to unwind.
Here are the eight steps I actually run. Not in textbook order. In the order I run them when someone calls me from a warehouse at 7 pm.
Step 1: Pin down the chemistry before you touch anything
Lithium-ion, LFP, sodium-ion, or solid-state. They fail differently and they need different disposal paths.
The label is your first stop: cell number, chemistry code, nominal voltage. Don't trust the brand sticker alone—I've seen "LFP" markings on cells that tested as NMC once I got them on a bench.
This matters more than it did two years ago. CATL's new sodium-ion cells are finally moving into commercial supply, and the trade-offs are different: lower energy density than LFP, better cold-weather performance, no lithium in the cathode. If your working assumption is "lithium battery = lithium-ion = same rules," the sodium-ion shift is a reminder that the category just got wider. The handling and disposal rules for sodium-ion are close to lithium-ion in practice, but the labeling and recycling partners are not always the same.
Step 2: Read the thermal signals
Before you test anything, look for swelling, puffy corners, discoloration around the terminals, a sweet or solvent smell, or warmth without recent usage.
Swollen cell? Stop. That's not a diagnostic question. That's a "quarantine box, gloves, and call someone" situation.
The order I check:
- Is the case deformed?
- Does it smell like anything other than plastic?
- Does it hold temperature after being unplugged for 10 minutes?
Any yes, and it goes to quarantine. Diagnostics can wait. Chemistry doesn't care about your deadline.
Step 3: Verify the charge/discharge pair
This is the step most people skip. A 12V solar panel charge controller and the battery need to agree on chemistry, voltage range, and charge profile.
A 12V solar charge controller preset for flooded lead-acid will overcharge an LFP pack. Not always immediately. But it will shorten the life, and it can push a marginal cell into a failure curve you didn't see coming. Flip side: if the controller was set up for LiFePO4 and the battery was swapped to a different chemistry without changing the profile, you've got a slow-motion problem that won't show up until the warranty window closes.
The Anker PowerHouse 535 is a useful reference case. It's a closed system—you don't pair it with a random solar controller, you use its built-in MPPT or a matched input. Once you break that pairing, you become the system integrator. Which means you own the spec.
Step 4: Isolate before you diagnose
Put the suspect cell or pack somewhere it can fail alone. Concrete is fine. Wood is fine. A metal shelf with other cells is not.
The rule I run by: if it fails right now, who else is affected? If the answer is "a shelf of inventory" or "the whole shipment," you're doing it wrong.
Step 5: Decide—repair, quarantine, or retire
Three buckets. Not two.
Repair: cell is healthy; the issue is a connector, a BMS board, or firmware.
Quarantine: cell health is unclear or marginal. It sits isolated with a date tag for 14 days.
Retire: confirmed failure, swelling, or a cell that won't accept or hold charge.
The mistake I see most often: treating "it works" as equivalent to "it's safe." A cell can run your load and still be on a failure curve. I assumed for years that a working pack was a safe pack. Didn't verify. Turned out the ones that fail catastrophically are often the ones that tested fine an hour before.
Step 6: Match the disposal path to the device
This is where the checklist gets boring and people stop reading. Stay with me. The disposal step is where most of the actual cost sits.
Batteries under 300 Wh can usually go through retail recycling programs—Home Depot, Best Buy, some municipal drop-offs. Bigger packs, like a 500 Wh portable power station, usually need a commercial recycler.
Embedded cells—phones, toys, small electronics—are the messy category. Take a sex toy with a lithium battery. It's a sealed device, the battery is not user-replaceable, and most curbside programs won't take it. The right answer is usually: household hazardous waste site that accepts batteries, or a battery recycler that accepts small embedded cells. If the cell is swollen, double-bag it and label it before transport.
I don't have hard data I can defend on how many of these devices get landfilled—my guess is most of them. But I do rely on one number: industry estimates put lithium-ion battery fires in US waste facilities in the thousands per year, and the EPA cites them as a leading cause of waste-facility fires. That trend is not going the right direction as portable power becomes more normal in households.
Step 7: Document the disposition
Date, chemistry, cell count, reason for retirement, where it went. Spreadsheet or a physical tag on the box.
This is the step I skipped for the first two years. I regret it. When a customer asks "what happened to the batch from March?" and you can't answer, you look like you were guessing.
Step 8: Close the loop with a visual check
After the disposal paperwork, walk back to where the device was. Is the shelf clear? Is there a bracket that looks stressed? A cable that got pinched when the unit was pulled out?
This is where prevention actually lives. Steps 1–7 get the immediate problem out of the building. Step 8 is what stops the next one.
What I got wrong
It took me about three years—closer to four if you count the two before I started tracking—to figure out that roughly 70% of the "emergency" battery calls I handled were a spec mismatch someone could have caught in a 90-second check. Not a manufacturing defect. Not a surprise. A chemistry mismatch, a controller setting, or a charger that wasn't matched to the pack.
I used to assume that matching voltage was enough. It isn't. Matching chemistry, charge profile, and temperature range is.
The other thing I got wrong: I treated disposal as someone else's problem for too long. If you sell or service battery-powered gear, disposal is your problem. The waste-facility fire numbers are a direct consequence of that assumption floating around the industry.
Five minutes of verification beats five days of correction. That's not a slogan—it's the reason this checklist exists.
The one non-step
Before you start any of this, ask yourself: how much time do I have?
If the answer is "not much," skip to Step 4, isolate the cell, and call a professional. The rest of the checklist assumes you have a couple of hours to think. Real emergencies don't.
Ask for engineering context